作业帮ansys 中如何在一个边上面加载一个线性变化的温度?目前本人加了一个定值是可以run的./file,base/prep7 /UNITS,sirectng,0,0.09,0,0.09rectng,0,0.09,0.18,0.27rectng,0.18,0.27,0.18,0.27rectng,0.18,0.27,0,0.09rectng,0,0.09,0.09,
来源：学生作业帮助网 编辑：作业帮 时间：2024/05/03 04:15:02
ansys 中如何在一个边上面加载一个线性变化的温度?目前本人加了一个定值是可以run的./file,base/prep7 /UNITS,sirectng,0,0.09,0,0.09rectng,0,0.09,0.18,0.27rectng,0.18,0.27,0.18,0.27rectng,0.18,0.27,0,0.09rectng,0,0.09,0.09,
ansys 中如何在一个边上面加载一个线性变化的温度?目前本人加了一个定值是可以run的.
/file,base
/prep7
/UNITS,si
rectng,0,0.09,0,0.09
rectng,0,0.09,0.18,0.27
rectng,0.18,0.27,0.18,0.27
rectng,0.18,0.27,0,0.09
rectng,0,0.09,0.09,0.18
rectng,0.09,0.18,0.18,0.27
rectng,0.09,0.18,0.09,0.18
rectng,0.09,0.18,0,0.09
rectng,0.18,0.27,0.09,0.18
aglue,all
et,1,plane55
mshape,0,2d
mp,c,1,450
mp,kxx,1,36.7
mp,dens,1,7870
mp,c,2,1
mp,kxx,2,9999999999
mp,dens,2,2
GUI
esize,0.01
amesh,all
FINISH
/SOLU
antype,trans
kbc,0
*SET,delt,1
timint,on
autots,off
nropt,full
/VIEW,1,1,1,1
/ANG,1
/REP,FAST
*do,i,1,100,1
/VIEW,1,1,1,1
/ANG,1
/REP,FAST
/GO
TIME,i*1
autots,0
DELTIM,1
KBC,0
DL,4,1,TEMP,200 我想把这里的温度改成线性变化的,按照坐标的变大而变大
DL,8,2,TEMP,200 我想把这里的温度改成线性变化的,按照坐标的变大而变大
DL,10,3,TEMP,15
DL,14,4,TEMP,15
allsel
SOLVE
*enddo
OUTRES,ALL,ALL,
/PSF,hflux,2
/replot
OUTRES,ALL,ALL,
FINISH
ansys 中如何在一个边上面加载一个线性变化的温度?目前本人加了一个定值是可以run的./file,base/prep7 /UNITS,sirectng,0,0.09,0,0.09rectng,0,0.09,0.18,0.27rectng,0.18,0.27,0.18,0.27rectng,0.18,0.27,0,0.09rectng,0,0.09,0.09,
分析如下：
首先就死内外螺纹必须精度高点,因为如果精度不算太高的话就会产生相互的轴向作用,这样将导致相咬的两轴之间会产生轴孔的变形,如果不及时的进行修正的话,那势必要影响内孔的精度,在装配精度轴时,会出现装不上的情况或者出现装上了在工件进行工作时轴与孔之间将产生摩擦力,这样的结果将会使精度零件报废.
其次就要用到《公差上配合与质量控制》上的同轴度必须要求一定的值这样的话就避免了出现不必要的影响上面一说明,不知道这个可不可以